Creativity Kick Starter

At times, do you find your creativity waning?

One thing I have done to combat this problem is to get a large three-ring binder and use it to hold examples of pottery, art, and designs that I find appealing. Many of these pages come from  magazines, post cards from art shows, and even pictures I taken of various forms of art. 

I also have many examples from the Internet. When I find a site or picture on a site that I like, I print it, and put it in my “Creativity” Book. It’s always a good idea to print anything you find on the Internet that you want to eventually refer to later versus just saving a bookmark, because the Internet is very dynamic and the content you find today may not be available tomorrow.

I usually put the pictures in a clear plastic 3 hole punched sleve to put in the binder.  These pages hold up much better than magazine paper and can hold small clippings when a full page is not needed.

Over time your book may become quite thick. Mine has grown from 1 inch to 3 inches. You can organize the content however you like.

Then when you are looking or inspiration you can start paging through your book for new ideas or directions to take your work. You may find a handle you want to experiment with on your style of mug, or an interesting foot treatment you want to try on your vase. I am always amazed at the picture I find in my book that I have forgotten about. I don’t recommend copying a piece exactly, but instead try to take the essence of the style, apply your own style, and create a new form.

 

Smokeless Raku

When you think of Raku, you probably think lots of smoke, and this is generally true, but there are a few techniques that can reduce or completely eliminate the amount of smoke that you have to deal with.

The first method involves using water over the reduction chamber. This works pretty good with garbage cans. After you place the piece in the garbage can and replace the lid, either spray or pour water over the top of the lid. The water quickly cools the lid, which causes the heated and expanded metal to shrink a bit. This provides a tighter seal and should reduce the amount of smoke that escapes from the container.

The second method also works well with garbage cans. In this case you place wet newspapers across the lid. After the piece is placed in the can, the lid containing the wet sheets of newspaper is placed over the can. The wet newspaper provides a better seal around the edge than just metal on metal.

The third method usually works better with smaller reduction chambers. This involves a sand pit. The piece is removed from the kiln and placed on a bed of combustible materials in a pit of sand. A metal container, such as a metal bucket, washtub, or even a garbage can, is placed upside down over the piece. The rim of the container is pushed into the sand, which provides almost an airtight seal. Additional sand can be pushed up around the rim if smoke is still escaping.

Finally the fourth method is the water lock. This method is very similar to the sand method but involves water instead of sand. This can work well using a metal tub and a very small garbage can. The piece is removed from the kiln and placed on a set of bricks in the metal tub. The tub contains a few inches of water that is below the height of the bricks. A small can is then placed upside down over the piece with the rim submerged into the water. This proved an airtight seal in which no smoke escapes. To keep the combustibles out of the water with this method, it works better to put the combustibles in the can that will be placed over the piece. This way as the can is placed over the piece to provide a seal, the combustibles in the bottom of the can fall onto the piece, ignite, and start the reduction process.

Each of these reduction methods will provide a new factor of the Raku process and may keep you from tearing up.

Resist-ing the Temptation of Glaze

Sometimes with Raku, what you don’t glaze is as exciting as what you do glaze and there are many methods of keeping portions of a piece free of glaze. In most cases, unglazed sections of a piece will turn black as smoke is absorbed into the bare clay during the reduction process. This is something to keep in mind that is different than other firing techniques. With other firings, unglazed clay typically remains clay color (white, buff, red, etc.) but with Raku the unglazed clay will turn black.

In most cases you will want to keep the foot of you piece free of glaze. This can be done with the use of a wax resist or masking tape. You can either dip the piece in a shallow pan of wax resist or brush a band around the bottom of the piece. As an alternative you can use masking tape and place a band of tape around the bottom of the piece. Either method should keep the piece free of glaze when spraying or brushing on glaze. If you dip the piece, the bottom of the piece will need to be waxed or covered with tape as well.

When the glaze has dried on the pot, you can take a damp sponge and remove any beaded glaze on the wax resist or remove the tape that has been applied. When removing the tape, make sure the glaze dust that is produced does not land on sections of the piece that you want to keep bare.

As a decorative effect you may want to leave part of the rim clear of glaze as well. This can be done just like the foot, with either a band of wax resist or a band of tape. In many cases I like to have a black band of bare clay at the top and bottom of my pieces.

In addition to the foot and rim, resist techniques can be used to provide some definite order and design to the dynamic and variable Raku process. You can use narrow strips of tape to create geometric designs (like southwestern or Celtic patterns). There are several examples of this on my website. You can draw the pattern on the piece and then place tape strips or brush wax resist over the design. Tape strips will provide a much more exacting and precise line, but you have to make sure the tape is strongly attached to keep the glaze from seeping under the tape.

Sometimes it is interesting to combine or overlap glazes on a piece, but sometimes the “mixing” is undesirable. Strips of tape or resist can be placed as a divider between different glazes to make sure they don’t “mix” during the firing process. This can produces a very distinct stained glass like affect depending on the pattern and glazes used.

Other patterns can be placed on a piece as well. For example, Chinese characters can be brushed on a piece using wax resist before the piece is glazed. Then the finished product will show a dark pattern in the unglazed clay surrounded with the Raku glaze.

Templates can be cut out of self-sticking shelf liner and placed on a piece to provide additional patterns, such as leaves, birds, symbols, or any other complex shape that is not easily painted with wax resist or created with strips of tape.

One thing you may want to consider when using these resist techniques is the amount of glazed that is applied right next to the resisted section. If a large amount of glaze is applied, and the glaze is runny at all, the intricate pattern you created may be ruined with drips.

Good Luck and Happy Resisting.